You are viewing this page in an unauthorized frame window.
This is a potential security issue, you are being redirected to
https://nvd.nist.gov
An official website of the United States government
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
Secure .gov websites use HTTPS
A lock () or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.
This CVE record has recently been published to the CVE List and has been included within the NVD dataset.
Description
In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add locking when updating filter and timer values
KCSAN detected a simultaneous access to timer values that can be
overwritten in bcm_rx_setup() when updating timer and filter content
while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler()
run concurrently on incoming CAN traffic.
Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter
(nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new
per-op bcm_rx_update_lock, taken with the matching scope in the RX
handlers. memcpy_from_msg() is staged into a temporary buffer before the
lock is taken, since it can sleep and must not run under a spinlock.
hrtimer_cancel() is always called without bcm_rx_update_lock held, since
bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a
running callback would otherwise deadlock against the canceller.
Also close a related race: bcm_rx_setup() cleared the RTR flag in the
stored reply frame's can_id as a separate, unprotected step after the
frame content was already installed, so a concurrent bcm_rx_handler()
could transmit a stale reply with CAN_RTR_FLAG still set. Fold that
normalization into the initial frame preparation instead (on the staged
buffer for updates, directly on op->frames pre-registration for new
ops), so the installed frame is always atomically self-consistent.
bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected
snapshot of op->flags before deciding whether to call bcm_can_tx(),
but does not hold the lock across that call.
Also take a lock-protected snapshot of the currframe in bcm_can_tx()
to avoid partly overwrites by content updates in bcm_tx_setup().
Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset
op->currframe between the two locked sections in bcm_can_tx().
Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler().
kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it
cancels this timer, so check kt_ival2 inside the bcm_rx_update_lock.
Metrics
NVD enrichment efforts reference publicly available information to associate
vector strings. CVSS information contributed by other sources is also
displayed.
By selecting these links, you will be leaving NIST webspace.
We have provided these links to other web sites because they
may have information that would be of interest to you. No
inferences should be drawn on account of other sites being
referenced, or not, from this page. There may be other web
sites that are more appropriate for your purpose. NIST does
not necessarily endorse the views expressed, or concur with
the facts presented on these sites. Further, NIST does not
endorse any commercial products that may be mentioned on
these sites. Please address comments about this page to [email protected].
In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add locking when updating filter and timer values
KCSAN detected a simultaneous access to timer values that can be
overwritten in bcm_rx_setup() when updating timer and filter content
while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler()
run concurrently on incoming CAN traffic.
Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter
(nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new
per-op bcm_rx_update_lock, taken with the matching scope in the RX
handlers. memcpy_from_msg() is staged into a temporary buffer before the
lock is taken, since it can sleep and must not run under a spinlock.
hrtimer_cancel() is always called without bcm_rx_update_lock held, since
bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a
running callback would otherwise deadlock against the canceller.
Also close a related race: bcm_rx_setup() cleared the RTR flag in the
stored reply frame's can_id as a separate, unprotected step after the
frame content was already installed, so a concurrent bcm_rx_handler()
could transmit a stale reply with CAN_RTR_FLAG still set. Fold that
normalization into the initial frame preparation instead (on the staged
buffer for updates, directly on op->frames pre-registration for new
ops), so the installed frame is always atomically self-consistent.
bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected
snapshot of op->flags before deciding whether to call bcm_can_tx(),
but does not hold the lock across that call.
Also take a lock-protected snapshot of the currframe in bcm_can_tx()
to avoid partly overwrites by content updates in bcm_tx_setup().
Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset
op->currframe between the two locked sections in bcm_can_tx().
Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler().
kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it
cancels this timer, so check k
) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.
