In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: Fix memcpy() field-spanning write warning in mwifiex_cmd_802_11_scan_ext() Replace one-element array with a flexible-array member in `struct host_cmd_ds_802_11_scan_ext`. With this, fix the following warning: elo 16 17:51:58 surfacebook kernel: ------------[ cut here ]------------ elo 16 17:51:58 surfacebook kernel: memcpy: detected field-spanning write (size 243) of single field "ext_scan->tlv_buffer" at drivers/net/wireless/marvell/mwifiex/scan.c:2239 (size 1) elo 16 17:51:58 surfacebook kernel: WARNING: CPU: 0 PID: 498 at drivers/net/wireless/marvell/mwifiex/scan.c:2239 mwifiex_cmd_802_11_scan_ext+0x83/0x90 [mwifiex]

In the Linux kernel, the following vulnerability has been resolved: ALSA: asihpi: Fix potential OOB array access ASIHPI driver stores some values in the static array upon a response from the driver, and its index depends on the firmware. We shouldn't trust it blindly. This patch adds a sanity check of the array index to fit in the array size.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix i_data_sem unlock order in ext4_ind_migrate() Fuzzing reports a possible deadlock in jbd2_log_wait_commit. This issue is triggered when an EXT4_IOC_MIGRATE ioctl is set to require synchronous updates because the file descriptor is opened with O_SYNC. This can lead to the jbd2_journal_stop() function calling jbd2_might_wait_for_commit(), potentially causing a deadlock if the EXT4_IOC_MIGRATE call races with a write(2) system call. This problem only arises when CONFIG_PROVE_LOCKING is enabled. In this case, the jbd2_might_wait_for_commit macro locks jbd2_handle in the jbd2_journal_stop function while i_data_sem is locked. This triggers lockdep because the jbd2_journal_start function might also lock the same jbd2_handle simultaneously. Found by Linux Verification Center (linuxtesting.org) with syzkaller. Rule: add

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: update DML2 policy EnhancedPrefetchScheduleAccelerationFinal DCN35 [WHY & HOW] Mismatch in DCN35 DML2 cause bw validation failed to acquire unexpected DPP pipe to cause grey screen and system hang. Remove EnhancedPrefetchScheduleAccelerationFinal value override to match HW spec. (cherry picked from commit 9dad21f910fcea2bdcff4af46159101d7f9cd8ba)

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix system hang while resume with TBT monitor [Why] Connected with a Thunderbolt monitor and do the suspend and the system may hang while resume. The TBT monitor HPD will be triggered during the resume procedure and call the drm_client_modeset_probe() while struct drm_connector connector->dev->master is NULL. It will mess up the pipe topology after resume. [How] Skip the TBT monitor HPD during the resume procedure because we currently will probe the connectors after resume by default. (cherry picked from commit 453f86a26945207a16b8f66aaed5962dc2b95b85)

In the Linux kernel, the following vulnerability has been resolved: static_call: Handle module init failure correctly in static_call_del_module() Module insertion invokes static_call_add_module() to initialize the static calls in a module. static_call_add_module() invokes __static_call_init(), which allocates a struct static_call_mod to either encapsulate the built-in static call sites of the associated key into it so further modules can be added or to append the module to the module chain. If that allocation fails the function returns with an error code and the module core invokes static_call_del_module() to clean up eventually added static_call_mod entries. This works correctly, when all keys used by the module were converted over to a module chain before the failure. If not then static_call_del_module() causes a #GP as it blindly assumes that key::mods points to a valid struct static_call_mod. The problem is that key::mods is not a individual struct member of struct static_call_key, it's part of a union to save space: union { /* bit 0: 0 = mods, 1 = sites */ unsigned long type; struct static_call_mod *mods; struct static_call_site *sites; }; key::sites is a pointer to the list of built-in usage sites of the static call. The type of the pointer is differentiated by bit 0. A mods pointer has the bit clear, the sites pointer has the bit set. As static_call_del_module() blidly assumes that the pointer is a valid static_call_mod type, it fails to check for this failure case and dereferences the pointer to the list of built-in call sites, which is obviously bogus. Cure it by checking whether the key has a sites or a mods pointer. If it's a sites pointer then the key is not to be touched. As the sites are walked in the same order as in __static_call_init() the site walk can be terminated because all subsequent sites have not been touched by the init code due to the error exit. If it was converted before the allocation fail, then the inner loop which searches for a module match will find nothing. A fail in the second allocation in __static_call_init() is harmless and does not require special treatment. The first allocation succeeded and converted the key to a module chain. That first entry has mod::mod == NULL and mod::next == NULL, so the inner loop of static_call_del_module() will neither find a module match nor a module chain. The next site in the walk was either already converted, but can't match the module, or it will exit the outer loop because it has a static_call_site pointer and not a static_call_mod pointer.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix error path in multi-packet WQE transmit Remove the erroneous unmap in case no DMA mapping was established The multi-packet WQE transmit code attempts to obtain a DMA mapping for the skb. This could fail, e.g. under memory pressure, when the IOMMU driver just can't allocate more memory for page tables. While the code tries to handle this in the path below the err_unmap label it erroneously unmaps one entry from the sq's FIFO list of active mappings. Since the current map attempt failed this unmap is removing some random DMA mapping that might still be required. If the PCI function now presents that IOVA, the IOMMU may assumes a rogue DMA access and e.g. on s390 puts the PCI function in error state. The erroneous behavior was seen in a stress-test environment that created memory pressure.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix NULL deref in mlx5e_tir_builder_alloc() In mlx5e_tir_builder_alloc() kvzalloc() may return NULL which is dereferenced on the next line in a reference to the modify field. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: improve shutdown sequence Alexander Sverdlin presents 2 problems during shutdown with the lan9303 driver. One is specific to lan9303 and the other just happens to reproduce there. The first problem is that lan9303 is unique among DSA drivers in that it calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown, not remove): phy_state_machine() -> ... -> dsa_user_phy_read() -> ds->ops->phy_read() -> lan9303_phy_read() -> chip->ops->phy_read() -> lan9303_mdio_phy_read() -> dev_get_drvdata() But we never stop the phy_state_machine(), so it may continue to run after dsa_switch_shutdown(). Our common pattern in all DSA drivers is to set drvdata to NULL to suppress the remove() method that may come afterwards. But in this case it will result in an NPD. The second problem is that the way in which we set dp->conduit->dsa_ptr = NULL; is concurrent with receive packet processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL, but afterwards, rather than continuing to use that non-NULL value, dev->dsa_ptr is dereferenced again and again without NULL checks: dsa_conduit_find_user() and many other places. In between dereferences, there is no locking to ensure that what was valid once continues to be valid. Both problems have the common aspect that closing the conduit interface solves them. In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN event in dsa_user_netdevice_event() which closes user ports as well. dsa_port_disable_rt() calls phylink_stop(), which synchronously stops the phylink state machine, and ds->ops->phy_read() will thus no longer call into the driver after this point. In the second case, dev_close(conduit) should do this, as per Documentation/networking/driver.rst: | Quiescence | ---------- | | After the ndo_stop routine has been called, the hardware must | not receive or transmit any data. All in flight packets must | be aborted. If necessary, poll or wait for completion of | any reset commands. So it should be sufficient to ensure that later, when we zeroize conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call on this conduit. The addition of the netif_device_detach() function is to ensure that ioctls, rtnetlinks and ethtool requests on the user ports no longer propagate down to the driver - we're no longer prepared to handle them. The race condition actually did not exist when commit 0650bf52b31f ("net: dsa: be compatible with masters which unregister on shutdown") first introduced dsa_switch_shutdown(). It was created later, when we stopped unregistering the user interfaces from a bad spot, and we just replaced that sequence with a racy zeroization of conduit->dsa_ptr (one which doesn't ensure that the interfaces aren't up).

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: lantiq_etop: fix memory disclosure When applying padding, the buffer is not zeroed, which results in memory disclosure. The mentioned data is observed on the wire. This patch uses skb_put_padto() to pad Ethernet frames properly. The mentioned function zeroes the expanded buffer. In case the packet cannot be padded it is silently dropped. Statistics are also not incremented. This driver does not support statistics in the old 32-bit format or the new 64-bit format. These will be added in the future. In its current form, the patch should be easily backported to stable versions. Ethernet MACs on Amazon-SE and Danube cannot do padding of the packets in hardware, so software padding must be applied.

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix buffer overflow when parsing NFS reparse points ReparseDataLength is sum of the InodeType size and DataBuffer size. So to get DataBuffer size it is needed to subtract InodeType's size from ReparseDataLength. Function cifs_strndup_from_utf16() is currentlly accessing buf->DataBuffer at position after the end of the buffer because it does not subtract InodeType size from the length. Fix this problem and correctly subtract variable len. Member InodeType is present only when reparse buffer is large enough. Check for ReparseDataLength before accessing InodeType to prevent another invalid memory access. Major and minor rdev values are present also only when reparse buffer is large enough. Check for reparse buffer size before calling reparse_mkdev().

In the Linux kernel, the following vulnerability has been resolved: tipc: guard against string buffer overrun Smatch reports that copying media_name and if_name to name_parts may overwrite the destination. .../bearer.c:166 bearer_name_validate() error: strcpy() 'media_name' too large for 'name_parts->media_name' (32 vs 16) .../bearer.c:167 bearer_name_validate() error: strcpy() 'if_name' too large for 'name_parts->if_name' (1010102 vs 16) This does seem to be the case so guard against this possibility by using strscpy() and failing if truncation occurs. Introduced by commit b97bf3fd8f6a ("[TIPC] Initial merge") Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: block: fix integer overflow in BLKSECDISCARD I independently rediscovered commit 22d24a544b0d49bbcbd61c8c0eaf77d3c9297155 block: fix overflow in blk_ioctl_discard() but for secure erase. Same problem: uint64_t r[2] = {512, 18446744073709551104ULL}; ioctl(fd, BLKSECDISCARD, r); will enter near infinite loop inside blkdev_issue_secure_erase(): a.out: attempt to access beyond end of device loop0: rw=5, sector=3399043073, nr_sectors = 1024 limit=2048 bio_check_eod: 3286214 callbacks suppressed

In the Linux kernel, the following vulnerability has been resolved: drm/stm: Avoid use-after-free issues with crtc and plane ltdc_load() calls functions drm_crtc_init_with_planes(), drm_universal_plane_init() and drm_encoder_init(). These functions should not be called with parameters allocated with devm_kzalloc() to avoid use-after-free issues [1]. Use allocations managed by the DRM framework. Found by Linux Verification Center (linuxtesting.org). [1] https://lore.kernel.org/lkml/u366i76e3qhh3ra5oxrtngjtm2u5lterkekcz6y2jkndhuxzli@diujon4h7qwb/

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: amdkfd_free_gtt_mem clear the correct pointer Pass pointer reference to amdgpu_bo_unref to clear the correct pointer, otherwise amdgpu_bo_unref clear the local variable, the original pointer not set to NULL, this could cause use-after-free bug.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/hdcp: Check GSC structure validity Sometimes xe_gsc is not initialized when checked at HDCP capability check. Add gsc structure check to avoid null pointer error.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix double free issue during amdgpu module unload Flexible endpoints use DIGs from available inflexible endpoints, so only the encoders of inflexible links need to be freed. Otherwise, a double free issue may occur when unloading the amdgpu module. [ 279.190523] RIP: 0010:__slab_free+0x152/0x2f0 [ 279.190577] Call Trace: [ 279.190580] <TASK> [ 279.190582] ? show_regs+0x69/0x80 [ 279.190590] ? die+0x3b/0x90 [ 279.190595] ? do_trap+0xc8/0xe0 [ 279.190601] ? do_error_trap+0x73/0xa0 [ 279.190605] ? __slab_free+0x152/0x2f0 [ 279.190609] ? exc_invalid_op+0x56/0x70 [ 279.190616] ? __slab_free+0x152/0x2f0 [ 279.190642] ? asm_exc_invalid_op+0x1f/0x30 [ 279.190648] ? dcn10_link_encoder_destroy+0x19/0x30 [amdgpu] [ 279.191096] ? __slab_free+0x152/0x2f0 [ 279.191102] ? dcn10_link_encoder_destroy+0x19/0x30 [amdgpu] [ 279.191469] kfree+0x260/0x2b0 [ 279.191474] dcn10_link_encoder_destroy+0x19/0x30 [amdgpu] [ 279.191821] link_destroy+0xd7/0x130 [amdgpu] [ 279.192248] dc_destruct+0x90/0x270 [amdgpu] [ 279.192666] dc_destroy+0x19/0x40 [amdgpu] [ 279.193020] amdgpu_dm_fini+0x16e/0x200 [amdgpu] [ 279.193432] dm_hw_fini+0x26/0x40 [amdgpu] [ 279.193795] amdgpu_device_fini_hw+0x24c/0x400 [amdgpu] [ 279.194108] amdgpu_driver_unload_kms+0x4f/0x70 [amdgpu] [ 279.194436] amdgpu_pci_remove+0x40/0x80 [amdgpu] [ 279.194632] pci_device_remove+0x3a/0xa0 [ 279.194638] device_remove+0x40/0x70 [ 279.194642] device_release_driver_internal+0x1ad/0x210 [ 279.194647] driver_detach+0x4e/0xa0 [ 279.194650] bus_remove_driver+0x6f/0xf0 [ 279.194653] driver_unregister+0x33/0x60 [ 279.194657] pci_unregister_driver+0x44/0x90 [ 279.194662] amdgpu_exit+0x19/0x1f0 [amdgpu] [ 279.194939] __do_sys_delete_module.isra.0+0x198/0x2f0 [ 279.194946] __x64_sys_delete_module+0x16/0x20 [ 279.194950] do_syscall_64+0x58/0x120 [ 279.194954] entry_SYSCALL_64_after_hwframe+0x6e/0x76 [ 279.194980] </TASK>

In the Linux kernel, the following vulnerability has been resolved: ksmbd: add refcnt to ksmbd_conn struct When sending an oplock break request, opinfo->conn is used, But freed ->conn can be used on multichannel. This patch add a reference count to the ksmbd_conn struct so that it can be freed when it is no longer used.

In the Linux kernel, the following vulnerability has been resolved: bpftool: Fix undefined behavior in qsort(NULL, 0, ...) When netfilter has no entry to display, qsort is called with qsort(NULL, 0, ...). This results in undefined behavior, as UBSan reports: net.c:827:2: runtime error: null pointer passed as argument 1, which is declared to never be null Although the C standard does not explicitly state whether calling qsort with a NULL pointer when the size is 0 constitutes undefined behavior, Section 7.1.4 of the C standard (Use of library functions) mentions: "Each of the following statements applies unless explicitly stated otherwise in the detailed descriptions that follow: If an argument to a function has an invalid value (such as a value outside the domain of the function, or a pointer outside the address space of the program, or a null pointer, or a pointer to non-modifiable storage when the corresponding parameter is not const-qualified) or a type (after promotion) not expected by a function with variable number of arguments, the behavior is undefined." To avoid this, add an early return when nf_link_info is NULL to prevent calling qsort with a NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: x86-android-tablets: Fix use after free on platform_device_register() errors x86_android_tablet_remove() frees the pdevs[] array, so it should not be used after calling x86_android_tablet_remove(). When platform_device_register() fails, store the pdevs[x] PTR_ERR() value into the local ret variable before calling x86_android_tablet_remove() to avoid using pdevs[] after it has been freed.