You are viewing this page in an unauthorized frame window.
This is a potential security issue, you are being redirected to
https://nvd.nist.gov
An official website of the United States government
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
Secure .gov websites use HTTPS
A lock () or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.
In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: gadget: Bail from dwc3_gadget_exit() if dwc->gadget is NULL
There exists a possible scenario in which dwc3_gadget_init() can fail:
during during host -> peripheral mode switch in dwc3_set_mode(), and
a pending gadget driver fails to bind. Then, if the DRD undergoes
another mode switch from peripheral->host the resulting
dwc3_gadget_exit() will attempt to reference an invalid and dangling
dwc->gadget pointer as well as call dma_free_coherent() on unmapped
DMA pointers.
The exact scenario can be reproduced as follows:
- Start DWC3 in peripheral mode
- Configure ConfigFS gadget with FunctionFS instance (or use g_ffs)
- Run FunctionFS userspace application (open EPs, write descriptors, etc)
- Bind gadget driver to DWC3's UDC
- Switch DWC3 to host mode
=> dwc3_gadget_exit() is called. usb_del_gadget() will put the
ConfigFS driver instance on the gadget_driver_pending_list
- Stop FunctionFS application (closes the ep files)
- Switch DWC3 to peripheral mode
=> dwc3_gadget_init() fails as usb_add_gadget() calls
check_pending_gadget_drivers() and attempts to rebind the UDC
to the ConfigFS gadget but fails with -19 (-ENODEV) because the
FFS instance is not in FFS_ACTIVE state (userspace has not
re-opened and written the descriptors yet, i.e. desc_ready!=0).
- Switch DWC3 back to host mode
=> dwc3_gadget_exit() is called again, but this time dwc->gadget
is invalid.
Although it can be argued that userspace should take responsibility
for ensuring that the FunctionFS application be ready prior to
allowing the composite driver bind to the UDC, failure to do so
should not result in a panic from the kernel driver.
Fix this by setting dwc->gadget to NULL in the failure path of
dwc3_gadget_init() and add a check to dwc3_gadget_exit() to bail out
unless the gadget pointer is valid.
Metrics
NVD enrichment efforts reference publicly available information to associate
vector strings. CVSS information contributed by other sources is also
displayed.
By selecting these links, you will be leaving NIST webspace.
We have provided these links to other web sites because they
may have information that would be of interest to you. No
inferences should be drawn on account of other sites being
referenced, or not, from this page. There may be other web
sites that are more appropriate for your purpose. NIST does
not necessarily endorse the views expressed, or concur with
the facts presented on these sites. Further, NIST does not
endorse any commercial products that may be mentioned on
these sites. Please address comments about this page to [email protected].
OR
*cpe:2.3:o:linux:linux_kernel:5.13:rc1:*:*:*:*:*:*
*cpe:2.3:o:linux:linux_kernel:5.13:rc2:*:*:*:*:*:*
*cpe:2.3:o:linux:linux_kernel:5.13:rc3:*:*:*:*:*:*
*cpe:2.3:o:linux:linux_kernel:5.13:rc4:*:*:*:*:*:*
*cpe:2.3:o:linux:linux_kernel:5.13:rc5:*:*:*:*:*:*
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 5.11 up to (excluding) 5.12.11
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 5.10 up to (excluding) 5.10.44
New CVE Received from kernel.org5/21/2024 11:15:15 AM
Action
Type
Old Value
New Value
Added
Description
In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: gadget: Bail from dwc3_gadget_exit() if dwc->gadget is NULL
There exists a possible scenario in which dwc3_gadget_init() can fail:
during during host -> peripheral mode switch in dwc3_set_mode(), and
a pending gadget driver fails to bind. Then, if the DRD undergoes
another mode switch from peripheral->host the resulting
dwc3_gadget_exit() will attempt to reference an invalid and dangling
dwc->gadget pointer as well as call dma_free_coherent() on unmapped
DMA pointers.
The exact scenario can be reproduced as follows:
- Start DWC3 in peripheral mode
- Configure ConfigFS gadget with FunctionFS instance (or use g_ffs)
- Run FunctionFS userspace application (open EPs, write descriptors, etc)
- Bind gadget driver to DWC3's UDC
- Switch DWC3 to host mode
=> dwc3_gadget_exit() is called. usb_del_gadget() will put the
ConfigFS driver instance on the gadget_driver_pending_list
- Stop FunctionFS application (closes the ep files)
- Switch DWC3 to peripheral mode
=> dwc3_gadget_init() fails as usb_add_gadget() calls
check_pending_gadget_drivers() and attempts to rebind the UDC
to the ConfigFS gadget but fails with -19 (-ENODEV) because the
FFS instance is not in FFS_ACTIVE state (userspace has not
re-opened and written the descriptors yet, i.e. desc_ready!=0).
- Switch DWC3 back to host mode
=> dwc3_gadget_exit() is called again, but this time dwc->gadget
is invalid.
Although it can be argued that userspace should take responsibility
for ensuring that the FunctionFS application be ready prior to
allowing the composite driver bind to the UDC, failure to do so
should not result in a panic from the kernel driver.
Fix this by setting dwc->gadget to NULL in the failure path of
dwc3_gadget_init() and add a check to dwc3_gadget_exit() to bail out
unless the gadget pointer is valid.