You are viewing this page in an unauthorized frame window.
This is a potential security issue, you are being redirected to
https://nvd.nist.gov
An official website of the United States government
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
Secure .gov websites use HTTPS
A lock () or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.
This CVE record has been updated after NVD enrichment efforts were completed. Enrichment data supplied by the NVD may require amendment due to these changes.
Description
In the Linux kernel, the following vulnerability has been resolved:
irqchip/sifive-plic: Fix frozen interrupt due to affinity setting
PLIC ignores interrupt completion message for disabled interrupt, explained
by the specification:
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the
claim/complete register. The PLIC does not check whether the completion
ID is the same as the last claim ID for that target. If the completion
ID does not match an interrupt source that is currently enabled for
the target, the completion is silently ignored.
This caused problems in the past, because an interrupt can be disabled
while still being handled and plic_irq_eoi() had no effect. That was fixed
by checking if the interrupt is disabled, and if so enable it, before
sending the completion message. That check is done with irqd_irq_disabled().
However, that is not sufficient because the enable bit for the handling
hart can be zero despite irqd_irq_disabled(d) being false. This can happen
when affinity setting is changed while a hart is still handling the
interrupt.
This problem is easily reproducible by dumping a large file to uart (which
generates lots of interrupts) and at the same time keep changing the uart
interrupt's affinity setting. The uart port becomes frozen almost
instantaneously.
Fix this by checking PLIC's enable bit instead of irqd_irq_disabled().
Metrics
NVD enrichment efforts reference publicly available information to associate
vector strings. CVSS information contributed by other sources is also
displayed.
By selecting these links, you will be leaving NIST webspace.
We have provided these links to other web sites because they
may have information that would be of interest to you. No
inferences should be drawn on account of other sites being
referenced, or not, from this page. There may be other web
sites that are more appropriate for your purpose. NIST does
not necessarily endorse the views expressed, or concur with
the facts presented on these sites. Further, NIST does not
endorse any commercial products that may be mentioned on
these sites. Please address comments about this page to [email protected].
OR
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 6.19 up to (excluding) 6.19.7
*cpe:2.3:o:linux:linux_kernel:7.0:rc1:*:*:*:*:*:*
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 6.13 up to (excluding) 6.18.17
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 6.2 up to (excluding) 6.6.130
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 6.7 up to (excluding) 6.12.77
*cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* versions from (including) 5.1 up to (excluding) 6.1.167
New CVE Received from kernel.org3/25/2026 7:16:23 AM
Action
Type
Old Value
New Value
Added
Description
In the Linux kernel, the following vulnerability has been resolved:
irqchip/sifive-plic: Fix frozen interrupt due to affinity setting
PLIC ignores interrupt completion message for disabled interrupt, explained
by the specification:
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the
claim/complete register. The PLIC does not check whether the completion
ID is the same as the last claim ID for that target. If the completion
ID does not match an interrupt source that is currently enabled for
the target, the completion is silently ignored.
This caused problems in the past, because an interrupt can be disabled
while still being handled and plic_irq_eoi() had no effect. That was fixed
by checking if the interrupt is disabled, and if so enable it, before
sending the completion message. That check is done with irqd_irq_disabled().
However, that is not sufficient because the enable bit for the handling
hart can be zero despite irqd_irq_disabled(d) being false. This can happen
when affinity setting is changed while a hart is still handling the
interrupt.
This problem is easily reproducible by dumping a large file to uart (which
generates lots of interrupts) and at the same time keep changing the uart
interrupt's affinity setting. The uart port becomes frozen almost
instantaneously.
Fix this by checking PLIC's enable bit instead of irqd_irq_disabled().
) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.
