In the Linux kernel, the following vulnerability has been resolved: ALSA: Fix deadlocks with kctl removals at disconnection In snd_card_disconnect(), we set card->shutdown flag at the beginning, call callbacks and do sync for card->power_ref_sleep waiters at the end. The callback may delete a kctl element, and this can lead to a deadlock when the device was in the suspended state. Namely: * A process waits for the power up at snd_power_ref_and_wait() in snd_ctl_info() or read/write() inside card->controls_rwsem. * The system gets disconnected meanwhile, and the driver tries to delete a kctl via snd_ctl_remove*(); it tries to take card->controls_rwsem again, but this is already locked by the above. Since the sleeper isn't woken up, this deadlocks. An easy fix is to wake up sleepers before processing the driver disconnect callbacks but right after setting the card->shutdown flag. Then all sleepers will abort immediately, and the code flows again. So, basically this patch moves the wait_event() call at the right timing. While we're at it, just to be sure, call wait_event_all() instead of wait_event(), although we don't use exclusive events on this queue for now.

In the Linux kernel, the following vulnerability has been resolved: eth: sungem: remove .ndo_poll_controller to avoid deadlocks Erhard reports netpoll warnings from sungem: netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398) WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c gem_poll_controller() disables interrupts, which may sleep. We can't sleep in netpoll, it has interrupts disabled completely. Strangely, gem_poll_controller() doesn't even poll the completions, and instead acts as if an interrupt has fired so it just schedules NAPI and exits. None of this has been necessary for years, since netpoll invokes NAPI directly.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix deadlock on SRQ async events. xa_lock for SRQ table may be required in AEQ. Use xa_store_irq()/ xa_erase_irq() to avoid deadlock.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Modify the print level of CQE error Too much print may lead to a panic in kernel. Change ibdev_err() to ibdev_err_ratelimited(), and change the printing level of cqe dump to debug level.

In the Linux kernel, the following vulnerability has been resolved: ftrace: Fix possible use-after-free issue in ftrace_location() KASAN reports a bug: BUG: KASAN: use-after-free in ftrace_location+0x90/0x120 Read of size 8 at addr ffff888141d40010 by task insmod/424 CPU: 8 PID: 424 Comm: insmod Tainted: G W 6.9.0-rc2+ [...] Call Trace: <TASK> dump_stack_lvl+0x68/0xa0 print_report+0xcf/0x610 kasan_report+0xb5/0xe0 ftrace_location+0x90/0x120 register_kprobe+0x14b/0xa40 kprobe_init+0x2d/0xff0 [kprobe_example] do_one_initcall+0x8f/0x2d0 do_init_module+0x13a/0x3c0 load_module+0x3082/0x33d0 init_module_from_file+0xd2/0x130 __x64_sys_finit_module+0x306/0x440 do_syscall_64+0x68/0x140 entry_SYSCALL_64_after_hwframe+0x71/0x79 The root cause is that, in lookup_rec(), ftrace record of some address is being searched in ftrace pages of some module, but those ftrace pages at the same time is being freed in ftrace_release_mod() as the corresponding module is being deleted: CPU1 | CPU2 register_kprobes() { | delete_module() { check_kprobe_address_safe() { | arch_check_ftrace_location() { | ftrace_location() { | lookup_rec() // USE! | ftrace_release_mod() // Free! To fix this issue: 1. Hold rcu lock as accessing ftrace pages in ftrace_location_range(); 2. Use ftrace_location_range() instead of lookup_rec() in ftrace_location(); 3. Call synchronize_rcu() before freeing any ftrace pages both in ftrace_process_locs()/ftrace_release_mod()/ftrace_free_mem().

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix use-after-free of timer for log writer thread Patch series "nilfs2: fix log writer related issues". This bug fix series covers three nilfs2 log writer-related issues, including a timer use-after-free issue and potential deadlock issue on unmount, and a potential freeze issue in event synchronization found during their analysis. Details are described in each commit log. This patch (of 3): A use-after-free issue has been reported regarding the timer sc_timer on the nilfs_sc_info structure. The problem is that even though it is used to wake up a sleeping log writer thread, sc_timer is not shut down until the nilfs_sc_info structure is about to be freed, and is used regardless of the thread's lifetime. Fix this issue by limiting the use of sc_timer only while the log writer thread is alive.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/mes: fix use-after-free issue Delete fence fallback timer to fix the ramdom use-after-free issue. v2: move to amdgpu_mes.c

In the Linux kernel, the following vulnerability has been resolved: rcu-tasks: Fix show_rcu_tasks_trace_gp_kthread buffer overflow There is a possibility of buffer overflow in show_rcu_tasks_trace_gp_kthread() if counters, passed to sprintf() are huge. Counter numbers, needed for this are unrealistically high, but buffer overflow is still possible. Use snprintf() with buffer size instead of sprintf(). Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/tsens: Fix null pointer dereference compute_intercept_slope() is called from calibrate_8960() (in tsens-8960.c) as compute_intercept_slope(priv, p1, NULL, ONE_PT_CALIB) which lead to null pointer dereference (if DEBUG or DYNAMIC_DEBUG set). Fix this bug by adding null pointer check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix potential glock use-after-free on unmount When a DLM lockspace is released and there ares still locks in that lockspace, DLM will unlock those locks automatically. Commit fb6791d100d1b started exploiting this behavior to speed up filesystem unmount: gfs2 would simply free glocks it didn't want to unlock and then release the lockspace. This didn't take the bast callbacks for asynchronous lock contention notifications into account, which remain active until until a lock is unlocked or its lockspace is released. To prevent those callbacks from accessing deallocated objects, put the glocks that should not be unlocked on the sd_dead_glocks list, release the lockspace, and only then free those glocks. As an additional measure, ignore unexpected ast and bast callbacks if the receiving glock is dead.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Reload only IB representors upon lag disable/enable On lag disable, the bond IB device along with all of its representors are destroyed, and then the slaves' representors get reloaded. In case the slave IB representor load fails, the eswitch error flow unloads all representors, including ethernet representors, where the netdevs get detached and removed from lag bond. Such flow is inaccurate as the lag driver is not responsible for loading/unloading ethernet representors. Furthermore, the flow described above begins by holding lag lock to prevent bond changes during disable flow. However, when reaching the ethernet representors detachment from lag, the lag lock is required again, triggering the following deadlock: Call trace: __switch_to+0xf4/0x148 __schedule+0x2c8/0x7d0 schedule+0x50/0xe0 schedule_preempt_disabled+0x18/0x28 __mutex_lock.isra.13+0x2b8/0x570 __mutex_lock_slowpath+0x1c/0x28 mutex_lock+0x4c/0x68 mlx5_lag_remove_netdev+0x3c/0x1a0 [mlx5_core] mlx5e_uplink_rep_disable+0x70/0xa0 [mlx5_core] mlx5e_detach_netdev+0x6c/0xb0 [mlx5_core] mlx5e_netdev_change_profile+0x44/0x138 [mlx5_core] mlx5e_netdev_attach_nic_profile+0x28/0x38 [mlx5_core] mlx5e_vport_rep_unload+0x184/0x1b8 [mlx5_core] mlx5_esw_offloads_rep_load+0xd8/0xe0 [mlx5_core] mlx5_eswitch_reload_reps+0x74/0xd0 [mlx5_core] mlx5_disable_lag+0x130/0x138 [mlx5_core] mlx5_lag_disable_change+0x6c/0x70 [mlx5_core] // hold ldev->lock mlx5_devlink_eswitch_mode_set+0xc0/0x410 [mlx5_core] devlink_nl_cmd_eswitch_set_doit+0xdc/0x180 genl_family_rcv_msg_doit.isra.17+0xe8/0x138 genl_rcv_msg+0xe4/0x220 netlink_rcv_skb+0x44/0x108 genl_rcv+0x40/0x58 netlink_unicast+0x198/0x268 netlink_sendmsg+0x1d4/0x418 sock_sendmsg+0x54/0x60 __sys_sendto+0xf4/0x120 __arm64_sys_sendto+0x30/0x40 el0_svc_common+0x8c/0x120 do_el0_svc+0x30/0xa0 el0_svc+0x20/0x30 el0_sync_handler+0x90/0xb8 el0_sync+0x160/0x180 Thus, upon lag enable/disable, load and unload only the IB representors of the slaves preventing the deadlock mentioned above. While at it, refactor the mlx5_esw_offloads_rep_load() function to have a static helper method for its internal logic, in symmetry with the representor unload design.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Discard command completions in internal error Fix use after free when FW completion arrives while device is in internal error state. Avoid calling completion handler in this case, since the device will flush the command interface and trigger all completions manually. Kernel log: ------------[ cut here ]------------ refcount_t: underflow; use-after-free. ... RIP: 0010:refcount_warn_saturate+0xd8/0xe0 ... Call Trace: <IRQ> ? __warn+0x79/0x120 ? refcount_warn_saturate+0xd8/0xe0 ? report_bug+0x17c/0x190 ? handle_bug+0x3c/0x60 ? exc_invalid_op+0x14/0x70 ? asm_exc_invalid_op+0x16/0x20 ? refcount_warn_saturate+0xd8/0xe0 cmd_ent_put+0x13b/0x160 [mlx5_core] mlx5_cmd_comp_handler+0x5f9/0x670 [mlx5_core] cmd_comp_notifier+0x1f/0x30 [mlx5_core] notifier_call_chain+0x35/0xb0 atomic_notifier_call_chain+0x16/0x20 mlx5_eq_async_int+0xf6/0x290 [mlx5_core] notifier_call_chain+0x35/0xb0 atomic_notifier_call_chain+0x16/0x20 irq_int_handler+0x19/0x30 [mlx5_core] __handle_irq_event_percpu+0x4b/0x160 handle_irq_event+0x2e/0x80 handle_edge_irq+0x98/0x230 __common_interrupt+0x3b/0xa0 common_interrupt+0x7b/0xa0 </IRQ> <TASK> asm_common_interrupt+0x22/0x40

In the Linux kernel, the following vulnerability has been resolved: net: fec: remove .ndo_poll_controller to avoid deadlocks There is a deadlock issue found in sungem driver, please refer to the commit ac0a230f719b ("eth: sungem: remove .ndo_poll_controller to avoid deadlocks"). The root cause of the issue is that netpoll is in atomic context and disable_irq() is called by .ndo_poll_controller interface of sungem driver, however, disable_irq() might sleep. After analyzing the implementation of fec_poll_controller(), the fec driver should have the same issue. Due to the fec driver uses NAPI for TX completions, the .ndo_poll_controller is unnecessary to be implemented in the fec driver, so fec_poll_controller() can be safely removed.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix potential index out of bounds in color transformation function Fixes index out of bounds issue in the color transformation function. The issue could occur when the index 'i' exceeds the number of transfer function points (TRANSFER_FUNC_POINTS). The fix adds a check to ensure 'i' is within bounds before accessing the transfer function points. If 'i' is out of bounds, an error message is logged and the function returns false to indicate an error. Reported by smatch: drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:405 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.red' 1025 <= s32max drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:406 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.green' 1025 <= s32max drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_cm_common.c:407 cm_helper_translate_curve_to_hw_format() error: buffer overflow 'output_tf->tf_pts.blue' 1025 <= s32max

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Add 0 size check to mtk_drm_gem_obj Add a check to mtk_drm_gem_init if we attempt to allocate a GEM object of 0 bytes. Currently, no such check exists and the kernel will panic if a userspace application attempts to allocate a 0x0 GBM buffer. Tested by attempting to allocate a 0x0 GBM buffer on an MT8188 and verifying that we now return EINVAL.

In the Linux kernel, the following vulnerability has been resolved: media: atomisp: ssh_css: Fix a null-pointer dereference in load_video_binaries The allocation failure of mycs->yuv_scaler_binary in load_video_binaries() is followed with a dereference of mycs->yuv_scaler_binary after the following call chain: sh_css_pipe_load_binaries() |-> load_video_binaries(mycs->yuv_scaler_binary == NULL) | |-> sh_css_pipe_unload_binaries() |-> unload_video_binaries() In unload_video_binaries(), it calls to ia_css_binary_unload with argument &pipe->pipe_settings.video.yuv_scaler_binary[i], which refers to the same memory slot as mycs->yuv_scaler_binary. Thus, a null-pointer dereference is triggered.

In the Linux kernel, the following vulnerability has been resolved: drm: vc4: Fix possible null pointer dereference In vc4_hdmi_audio_init() of_get_address() may return NULL which is later dereferenced. Fix this bug by adding NULL check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix UAF for cq async event The refcount of CQ is not protected by locks. When CQ asynchronous events and CQ destruction are concurrent, CQ may have been released, which will cause UAF. Use the xa_lock() to protect the CQ refcount.

In the Linux kernel, the following vulnerability has been resolved: lib/test_hmm.c: handle src_pfns and dst_pfns allocation failure The kcalloc() in dmirror_device_evict_chunk() will return null if the physical memory has run out. As a result, if src_pfns or dst_pfns is dereferenced, the null pointer dereference bug will happen. Moreover, the device is going away. If the kcalloc() fails, the pages mapping a chunk could not be evicted. So add a __GFP_NOFAIL flag in kcalloc(). Finally, as there is no need to have physically contiguous memory, Switch kcalloc() to kvcalloc() in order to avoid failing allocations.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: xmit: make sure we have at least eth header len bytes syzbot triggered an uninit value[1] error in bridge device's xmit path by sending a short (less than ETH_HLEN bytes) skb. To fix it check if we can actually pull that amount instead of assuming. Tested with dropwatch: drop at: br_dev_xmit+0xb93/0x12d0 [bridge] (0xffffffffc06739b3) origin: software timestamp: Mon May 13 11:31:53 2024 778214037 nsec protocol: 0x88a8 length: 2 original length: 2 drop reason: PKT_TOO_SMALL [1] BUG: KMSAN: uninit-value in br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65 br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547 __dev_queue_xmit+0x34db/0x5350 net/core/dev.c:4341 dev_queue_xmit include/linux/netdevice.h:3091 [inline] __bpf_tx_skb net/core/filter.c:2136 [inline] __bpf_redirect_common net/core/filter.c:2180 [inline] __bpf_redirect+0x14a6/0x1620 net/core/filter.c:2187 ____bpf_clone_redirect net/core/filter.c:2460 [inline] bpf_clone_redirect+0x328/0x470 net/core/filter.c:2432 ___bpf_prog_run+0x13fe/0xe0f0 kernel/bpf/core.c:1997 __bpf_prog_run512+0xb5/0xe0 kernel/bpf/core.c:2238 bpf_dispatcher_nop_func include/linux/bpf.h:1234 [inline] __bpf_prog_run include/linux/filter.h:657 [inline] bpf_prog_run include/linux/filter.h:664 [inline] bpf_test_run+0x499/0xc30 net/bpf/test_run.c:425 bpf_prog_test_run_skb+0x14ea/0x1f20 net/bpf/test_run.c:1058 bpf_prog_test_run+0x6b7/0xad0 kernel/bpf/syscall.c:4269 __sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5678 __do_sys_bpf kernel/bpf/syscall.c:5767 [inline] __se_sys_bpf kernel/bpf/syscall.c:5765 [inline] __x64_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5765 x64_sys_call+0x96b/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f